Return to site

Transform your French Country Furniture with Fusion Mineral Paint

Monday French Country Crafts

· Older Posts,French Country Craft,French Country Decor,Country French Decor

Authentic French Country style furniture often boasts years of paint layers and subtle colour blends,

I'm excited to share this with you because although https://fusionmineralpaint.com/french-country-look/ shared this using Fusion Mineral Products, we're going to be using different products that are not so expensive as the gorgeous paints that she sells.

Materials

  • TSP
  • (2) quarts of latex paint
  • Kilz Primer - 1 quart
  • Pale Gold and Bronze acrylic paints
  • Plaster of Paris
  • Lot's of different size chip brushes
  • Stiff bristle brush or tooth brush
  • Light Sandpaper
  • Furniture wax

Step 1. Prep any furniture piece for painting is actually not sanding….it’s cleaning! While it may seem counterproductive to clean and then sand, there’s a good reason for doing it in this order.

Most older pieces of furniture have a build up of furniture polish or wax and disguised grime. If we sand a piece that hasn’t been cleaned well first, sanding can push the polish/wax/grime into the substrate creating small areas where the paint may be resisted.

Fusion’s TSP is very different from the store bought version of TSP and is completely VOC free. It cleans and removes grease and there’s no need to rinse it off before painting. Just one cap full per 500 ml (pint) of water is all that is needed.

Purchase a 1 qt bottle of TSP liquid from Home Depot for $5.50

Use a stiff bristled brush or toothbrush to get the grime out from all the detailed areas and a green kitchen scrubbie to clean the flat areas. Remove all hardware and give that a good scrub too.

Tie some string through each of the drawer pull holes for easy handling.

This piece was veneer and therefore very sleek. Veneer is very smooth and sanding makes little difference in keying the surface. A very thin layer of Fusion’s Ultra Grip painted over veneer provides superior adhesion on hard to paint surfaces such as veneer.

Step 2. PAINT. Choose two complimentary Fusion colors. Here we used Linen and Putty.

So here, you can simply purchase latex paint in the Linen and Putty colors shown.

First paint a full base coat of Putty over the whole piece.

Using a mini microfibre roller on all the larger flat areas is a huge time saver. Allow this first coat of paint to dry for a full 12 hours.

Step 3. FRESCO. There are no hard and fast rules to using Fusion’s Fresco. It’s a bit of experimentation all around. As a general rule the more Fresco you add to your paint the thicker it becomes and the more crusty the finish.

We're going to be using plaster of paris to thicken our paint. The same rules apply to our recipe using plaster of paris instead of Fushion Fresco.

You can make it super thick and trowel it on, then use a heat gun or blow dryer to achieve some impressive cracking! If you add a little too much Fresco and your mixture is too dry just add some extra paint or a little water and mix. To create a bit of texture or to accentuate brush marks add less powder. Just enough to thicken your paint.

For this project the mix needed to be thin enough to paint it on while still retaining some chunkiness, so that after a short time it could be troweled to spread and blended with the second color.

Pour some of the darker of your chosen colors (in this case, Linen) into a plastic disposable container and add Fresco until you have a sloppy cottage cheese type mix. Paint it on randomly, some dabs and some longer strokes. Start on a small area like a door first so you get the hang of it before working on the larger sections like the top and sides. Leave any chunky bits and don’t be tempted to flatten them yet!

Use an old paint brush to apply your Fresco or commit to rinsing it clean after each section. This is one time that wrapping your brush in plastic until the next coat just won’t do. If you forget, you’ll be the proud owner of a concrete paint brush!

Once your Fresco mix is made up you have about 10-15 minutes to use it before it starts becoming too hard to spread so don’t mix up more than you can deal with in that space of time and work in manageable sections.

Notice how thick it is when painting it on.

Repeat the process with your lighter color (Putty). A little less of the second color is needed.

Paint shorter strokes of the Putty. At this stage it may look like a camouflage finish but it’s now that the magic begins!

STEP 4. BLENDING. While both colors are still pliable, take an artists trowel and gently drag it through the two colors, blending while taking care not to flatten the texture too much. In the areas that lose a bit too much texture, pounce them with the flat side of the trowel to add some texture back.

Here their troweling on the second color and blending the two colors with the spatula.

Then you can go over areas with your trowel smoothing out the layered paint.

Use a shop rag to continue smoothing out the two colors of textured paint.

This is your canvas. You can go back over areas to add more texture to them.

Then because you only did small areas, you can smooth them with your shop rag.

FURNITURE PAINT TIP: When the piece of furniture has drawers, it can be a good idea to leave them in so the texture pattern flows over the whole area. Make sure to pull each drawer out a little and run your trowel along the edges so the chunks don’t dry there.

STEP 5. DETAILS. When the paint is about 90% dry (approx 15 minutes) run your finger along the detailed areas just to smooth it down a little more. Wear gloves for this bit!

STEP 6. SANDING. Once the piece is completely dry, give it a light sand just to remove any rough bits that aren’t smooth. There are usually a few peaks that need to be lightly sanded.

STEP 7. DRY BRUSH. The next step is to add some extra contrast with dry brushing. Load a short bristle stiff brush (chip brushes trimmed shorter are great!) with your lighter color (Linen). Dry brushing is exactly that, brushing with an almost dry brush. After dipping your brush in the paint, wipe 95% of the paint off onto some folded paper towel before lightly sweeping the brush over the surface of the textured paint. Pay particular attention to the areas that are the most textured as the high areas will catch the paint.

STEP 8. METALLIC DETAILS. Now, most authentic French Country style furniture seems to feature some gold detail. It’s easy to make a faux Tempura finish by mixing two of Fusion’s Metallic colors, 2 parts Pale Gold and 1 part Bronze. Use the same dry brushing method to brush some ‘aged gold’ over any raised detail areas and around the upper & lower edges. For finer detail use a small artists brush.

These are two colors that you can purchase as acrylic paints at the hobby store.

STEP 9. FINISHING TOUCHES. Fix any hardware back in place. The handles were switched out on this piece to a more French inspired style, so the same faux tempura mix was dry brushed over the new hardware to compliment the gold detail.

STEP 10. WAX. Fresco can be quite grainy to the touch, so we have waxed just the top of this piece to make dusting a little easier. Using a wax brush, work the wax over the entire surface before wiping back any excess with a lint free cloth.

Ahh....I couldn't help myself. I came across this gorgeous lamp and knew that we could make one ourselves.

If you love these colors with the cream and grey, than purchase these two colors in acrylic paint.

You'll follow the steps above to create this as well.

All Posts
×

Almost done…

We just sent you an email. Please click the link in the email to confirm your subscription!

OK